Brick Paver Installation & Edging



Staging of material

A lot of paver jobs will vary depending on gain access to, website conditions, job size and of course, the weather. Careful factor to consider must be taken to identify the time to start the paver installation.

The supervisor or job manager should constantly have the products (sand/ pavers) distributed around the task website for effective and easy installations. Paver pallets/bundles ought to be placed in a way not to disrupt the paver installation. The proper pallet/bundle placement can make the real job installation simpler and quicker by minimizing the total labor of dealing with the material.

Brick paver patterns

Pavers can be positioned in various patterns depending on their shape. Each paver shape will usually have a number of different hatch patterns that are provided by the maker.

Contractors require to take into consideration the traffic weight loads on their paver tasks. In a lot of applications worldwide, it has actually been shown that pavers laid in a herringbone pattern have actually performed effectively.

Pavers that are 60 mm (2 - 3/8 in) density are suitable for pedestrian applications. Pavers that are going to be utilized in commercial or industrial applications should be 80 mm (3 - 1/8 in) in density.

Reference/starting point for brick paver installation

There are a number of conditions that identify the starting point of a paver project.

When starting to set up pavers it is best to snap a true straight chalk line on the surface of the bed linen sand or pull a true straight string line above the surface area of the bedding sand at the completed elevation of the pavers This will help as a guide for preserving straight joint lines and will also enable the installer to make adjustments in the positioning of the pavers.

Buildings and concrete suppressing are generally not straight and must not be used for developing straight joint lines. The usage of string lines is essential to identify the true straightness of the edge. As the paver installation advances, the string lines will assist lessen the requirement for small trim pieces.

These will preserve a minimum joint width and permit the bedding and jointing sand to go into in between each paver. Pavers with spacer bars are generally not laid in snug versus each other since a string line will offer consistent joint spacing.

Installation of brick pavers.

Among the most widely used approaches for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have pulled or above the bedding sand. This will provide you a true and straight line off which to work. When this row is developed, you can continue to work outward into the field with the rest of the pavers. Constantly make certain to periodically inspect your joint lines to make sure they are real and straight. If not, modifications to the pavers can be made as you continue setting up. Pavers should be installed hand tight. The very best approach is to place a paver against another one and let it move down into the bed linen sand. Do not kick or tap the pavers into place as this can toss your lines out of true straightness.

When installing pavers on a high grade, they need to be installed at the base of the grade going uphill. This will prevent the pavers from creeping as they are being laid.

The finest method for installing pavers on big tasks is to install them mechanically. There are a couple items a contractor ought to think about prior to setting up pavers mechanically:

1.) Mechanical installers are just capable of setting up pavers in particular patterns.

2.) The specialist needs to make sure that the manufacturer is capable of manufacturing and bundling pavers in the preferred pattern on the pallets for simple mechanical installation.

3.) Specialists might come across a color mixing situation coming off the bundles of pavers Poor color blending could lead to an irregular looking installation. The majority of makers are consistent with color blending on each bundle of pavers, but it is the contractor's obligation to guarantee appropriate mixing in the field.

Cutting procedures for brick pavers.

Contractors generally have two ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will provide a much cleaner and more accurate cut. Most brick saws will have a hose attachment on them which will allow the operator to cut the pavers wet. When cutting pavers wet, it will help reduce dust and will prolong the diamond blades life. The operator of the brick saw ought to always cut the pavers away from the surface of the paver field when cutting wet, due to the fact that the pavers will create a slurry that will stain the paver surface. Pavers that are cut should not fit tight, sufficient spacing must be offered for jointing sand.

The brick saw operator should always use the correct security that is needed for operating a saw, such as eye, ear, respiratory and hand protection ).

Edging types

Edge restraints play a significant function in the general success of an interlocking pavement installation Edging restraints get rid of lateral movement of the pavers and hold the pavers tightly together. Especially at the external border of the paver application, without an edging restraint, your job is guaranteed to fail over time.

There are numerous various edging restraints from which professionals can select. Generally manufactured edge restraints are the most typically used by contractors. Made edging restraints can vary from, plastic edging, steel and aluminum, woods or precast concrete and stone. An edging type that is used primarily in business and commercial applications is poured-in-place concrete curbs. This edging restraint is usually installed by other contractors.

Edging installation.

When installing your edge restraint, it ought to rest directly on top of the compressed gravel base. The compacted gravel base course should extend a minimum of 6in beyond the border of the pavers This will supply a proper structure upon which the edging restraint can sit. Produced edging (i.E. Plastic, steel or aluminum) should be strongly anchored into the compressed gravel base( consult the manufacturer's literature for the advised spacing of the spikes). There are some edging restraints that will extend deeper into the gravel base or beyond the base course (i.E. Timbers or poured-in-place curbs ). Edging restraints need to never ever be positioned straight on top of the bed linen sand. This could lead to the migration of the bedding sand and eventual lateral motion of the pavers. If there is a possibility of losing bedding sand between the pavers and the edge restraint, then geo textile material is recommended. When a gap between the pavers and the edging goes beyond 3/8" (10mm), then the space needs to be filled with cut pavers. All edging applications must be correctly back filled after they are set up to assist provide extra stability.

Compaction of brick pavers.

After installation, the pavers need to be compressed. The entire location that is to be compacted need to be swept clean of any foreign things and particles that can cause scuffing or scratching on the surface of the pavers.

In addition, it is important that the very first compaction takes location before any jointing sand has actually been applied to the pavers. If jointing sand is applied to the pavers prior to compaction takes place, this can trigger a bridging problem and will not enable the joints to be entirely filled with jointing sand. This can also avoid the pavers from being correctly set into the bed linen sand.

When compacting the pavers, it is suggested that you make a minimum of two passes in various directions across the pavers. This will permit the pavers to be correctly embeded in the bedding sand and will force the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is very vital to the final performance of the pavers. Failure to do correct compaction can result in contortions and pavement failure with time.


Paver pallets/bundles ought to be positioned in a manner not to interfere with the paver installation. Tree Service Del Ray Beach One of the most commonly utilized methods for the installation of pavers is hand installation of each paver. The operator of the brick saw must constantly cut the pavers away from the surface of the paver field when cutting damp, due to the reality that the pavers will create a slurry that will stain the paver surface area. Edging restraints remove lateral motion of the pavers and hold the pavers firmly together. When a space between the pavers and the edging surpasses 3/8" (10mm), then the area should be filled with cut pavers.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Brick Paver Installation & Edging”

Leave a Reply

Gravatar